PET bottle crusher to reduce fines during PET bottle crushing for plastic recycling

Practical Methods to Reduce Fines During PET Bottle Crushing & Avoid Material Loss

 

PET bottles feature thin walls and high toughness; improper equipment selection or parameter settings during shredding can easily generate large amounts of fines. This not only causes material loss but also severely impacts the yield of subsequent washing and granulation processes. Based on the material characteristics of PET recycling, the following are targeted strategies to reduce fines:

 

 

1. Equipment Selection and Structural Optimization (Controlling Fines at the Source)

① Adopt a “Wet Shredding” Process

Introducing circulating water into the shredding chamber to perform shredding in a wet environment is a standard practice in PET recycling lines to minimize fines. The water flow provides lubrication and cooling, reducing heat generated by friction between the blades and the material (thereby preventing PET from softening, sticking, and creating fines). Additionally, the impact force of the water accelerates the discharge of properly sized flakes, reducing repeated cutting within the chamber. Wet shredding also serves as a preliminary washing step, removing some dirt and impurities.

 

② Increase Screen Area to Avoid Repeated Shearing

The area of ​​the screen on the side of the shredder directly determines the discharge speed. If the screen area is too small, properly sized flakes cannot be discharged promptly; they remain in the chamber to be repeatedly cut and ground by the blades, leading to a sharp increase in fines. Enlarging the screen area—ensuring material is discharged quickly once it reaches the target particle size—is a crucial structural optimization for reducing fines.

 

③ Equip with Forced Feeding/Screw Feeding Devices

PET mineral water bottles are hollow, elastic containers; standard feeding methods often cause them to bounce inside the chamber, resulting in uneven shredding and repeated cutting. Specialized PET shredders equipped with screw-driven forced feeding or forced-pressure plates flatten the bottles before pushing them into the cutting chamber. This ensures a clean, single-pass shearing action, which boosts throughput while preventing excessive shredding caused by material bouncing.

 

PET bottle crusher for PET recycling

 

2. Blade Selection and Process Parameter Control

① Select High-Hardness, Wear-Resistant Blade Materials

Although PET bottles have thin walls, the material itself is quite hard, and recycled feedstock inevitably contains small amounts of impurities. Rapid blade wear dulls the cutting edge, shifting the action from “cutting” to “grinding,” which significantly increases the generation of fines. It is recommended to use SKD-11, D2, or cemented carbide (such as YG8) for the rotary and stationary blades, with hardness controlled within the HRC 58–62 range. Sharp blades ensure clean, precise cutting, lower the cost of shredding per ton, and result in clean flake shapes with minimal fines.

 

② Properly control shredding particle size to avoid over-shredding

The standard shredding size for PET bottle recycling is typically 12–35 mm. If screen apertures are set too small in pursuit of smaller flakes (e.g., shredding directly to under 12 mm), material loss due to fines increases significantly. A two-stage process—combining coarse and fine shredding—is recommended, or the shredding size can be set directly within the 20–35 mm range; this meets downstream washing and sorting requirements while maximizing material integrity.

 

③ Precisely adjust the clearance between rotary and stationary blades

The gap between the rotary and stationary blades must be finely adjusted based on the thickness of the PET bottle walls. If the gap is too wide, bottle flakes may not cut through completely, resulting in connected strands; if the gap is too narrow, blade friction intensifies, leading to rapid heat buildup and the generation of excessive fine powder. Regular shutdowns are required to inspect and adjust the blades to the optimal cutting clearance.

 

 

Summary and Recommendations:

For shredding PET mineral water bottles, the most effective measures to reduce fines are “wet shredding” and the use of “large-area screens.” When planning or upgrading a production line, it is advisable to prioritize specialized PET shredders equipped with water-cooling systems and wear-resistant blades (such as SKD-11). Addressing both equipment specifications and process parameters is essential to minimizing material loss from fines. 

 

Welcome to check our newest design crusher machinery, one set can up to 3T/H capacity. Feel free to contact us if you are interested.

Request a Quote
All products are guaranteed for 12 months!